POWER SUPPLY
A power supply unit (PSU) converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies. Some power supplies have a manual switch for selecting input voltage, while others automatically adapt to the mains voltage.
WORKING OF POWER SUPPLY Power supplies, often referred to as "switching power supplies", use switcher technology to convert the AC input to lower DC voltages. The typical voltages supplied are:
3.3 volts
5 volts
12 volts
The 3.3- and 5-volts are typically used by digital circuits, while the 12-volt is used to run motors in disk drives and fans. The main specification of a power supply is in watts. A watt is the product of the voltage in volts and the current in amperes or amps. If you have been around PCs for many years, you probably remember that the original PCs had large red toggle switches that had a good bit of heft to them. When you turned the PC on or off, you knew you were doing it. These switches actually controlled the flow of 120 volt power to the power supply.
Today you turn on the power with a little push button, and you turn off the machine with a menu option. These capabilities were added to standard power supplies several years ago. The operating system can send a signal to the power supply to tell it to turn off. The push button sends a 5-volt signal to the power supply to tell it when to turn on. The power supply also has a circuit that supplies 5 volts, called VSB for "standby voltage" even when it is officially "off", so that the button will work. See the next page to learn more about switcher technology.
Switcher Technology Prior to 1980 or so, power supplies tended to be heavy and bulky. They used large, heavy transformers and huge capacitors (some as large as soda cans) to convert line voltage at 120 volts and 60 hertz into 5 volts and 12 volts DC. The switching power supplies used today are much smaller and lighter. They convert the 60-Hertz (Hz, or cycles per second) current to a much higher frequency, meaning more cycles per second. This conversion enables a small, lightweight transformer in the power supply to do the actual voltage step-down from 110 volts (or 220 in certain countries) to the voltage needed by the particular computer component. The higher-frequency AC current provided by a switcher supply is also easier to rectify and filter compared to the original 60-Hz AC line voltage, reducing the variances in voltage for the sensitive electronic components in the computer. A switcher power supply draws only the power it needs from the AC line. The typical voltages and current provided by a power supply are shown on the label on a power supply.
Switcher technology is also used to make AC from DC, as found in many of the automobile power inverters used to run AC appliances in an automobile and in uninterruptible power supplies. Switcher technology in automotive power inverters changes the direct current from the auto battery into alternating current. The transformer uses alternating current to make the transformer in the inverter step the voltage up to that of household appliances (120 VAC).
Power Supply Standardization Over time, there have been at least six different standard power supplies for personal computers. Recently, the industry has settled on using ATX-based power supplies. ATX is an industry specification that means the power supply has the physical characteristics to fit a standard ATX case and the electrical characteristics to work with an ATX motherboard.
PC power-supply cables use standardized, keyed connectors that make it difficult to connect the wrong ones. Also, fan manufacturers often use the same connectors as the power cables for disk drives, allowing a fan to easily obtain the 12 volts it needs. Color-coded wires and industry standard connectors make it possible for the consumer to have many choices for a replacement power supply.
Advanced Power Management (APM) offers a set of five different states that your system can be in. It was developed by Microsoft and Intel for PC users who wish to conserve power. Each system component, including the operating system, basic input/output system (BIOS), motherboard and attached devices all need to be APM-compliant to be able to use this feature. Should you wish to disable APM because you suspect it is using up system resources or causing a conflict, the best way to do this is in the BIOS. That way, the operating system won't try to reinstall it, which could happen if it were disabled only in the software.
Power Supply Wattage A 400-watt switching power supply will not necessarily use more power than a 250-watt supply. A larger supply may be needed if you use every available slot on the motherboard or every available drive bay in the personal computer case. It is not a good idea to have a 250-watt supply if you have 250 watts total in devices, since the supply should not be loaded to 100 percent of its capacity. According to PC Power & Cooling, Inc., some power consumption values (in watts) for common items in a personal computer are:
Accelerated Graphics Port (AGP) card = 20 to 30W
Peripheral Component Interconnect (PCI) card = 5W
small computer system interface (SCSI) PCI card = 20 to 25W
network interface card = 4W
50X CD-ROM drive = 10 to 25W
RAM = 10W per 128M
5200 RPM Integrated Drive Electronics (IDE) hard disk drive = 5 to 11W
7200 RPM IDE hard disk drive = 5-15W
Motherboard (without CPU or RAM) = 20 to 30W
550 MHz Pentium III = 30W
733 MHz Pentium III = 23.5W
300 MHz Celeron = 18W
600 MHz Athlon = 45W
Power supplies of the same form factor ("form factor" refers to the actual shape of the motherboard) are typically differentiated by the wattage they supply and the length of the warranty.
Power Supply Problems: The PC power supply is probably the most failure-prone item in a personal computer. It heats and cools each time it is used and receives the first in-rush of AC current when the PC is switched on. Typically, a stalled cooling fan is a predictor of a power supply failure due to subsequent overheated components. All devices in a PC receive their DC power via the power supply.
A typical failure of a PC power supply is often noticed as a burning smell just before the computer shuts down. Another problem could be the failure of the vital cooling fan, which allows components in the power supply to overheat. Failure symptoms include random rebooting or failure in Windows for no apparent reason. For any problems you suspect to be the fault of the power supply, use the documentation that came with your computer. If you have ever removed the case from your personal computer to add an adapter card or memory, you can change a power supply. Make sure you remove the power cord first since voltages are present even though your computer is off.
Power Supply Improvements: Recent motherboard and chipset improvements permit the user to monitor the revolutions per minute (RPM) of the power supply fan via BIOS and a Windows application supplied by the motherboard manufacturer. New designs offer fan control so that the fan only runs the speed needed, depending on cooling needs. Recent designs in Web servers include power supplies that offer a spare supply that can be exchanged while the other power supply is in use. Some new computers, particularly those designed for use as servers, provide redundant power supplies. This means that there are two or more power supplies in the system, with one providing power and the other acting as a backup. The backup supply immediately takes over in the event of a failure by the primary supply. Then, the primary supply can be exchanged while the other power supply is in use.
FOLLOW US ON INSTAGRAM, FACEBOOK AND PINTEREST
DISCLAIMER
The information is provided by Tecquisition for general informational and educational purposes only and is not a substitute for professional legal advice. If you have any feedback, comments, requests for technical support or other inquiries, please mail us by tecqusition@gmail.com.
Comments